Drill Press Redesign Project Design for Manufacture

Drill Press Redesign Project Design for Manufacture Drill press is the most vastly used mechanical machine around the world. Its usage is not limited to industries only, it is found and used even at homes in the form of portable or cordless drills. It is primarily used for cutting holes in specimen. Other functions that it can be used for include tapping, counter sinking, reaming, etc. There are three main types of drill press based on their versatility, size of workpiece it can handle and range. 1.1 Upright drill press First and the most commonly used type of drill press is Upright drill press. It consists of following main parts: (Groover, 2010) Base: It is the part that is in contact with the ground, it is made heavy to keep the drill bit from moving during operation. It can be bolted to the ground to keep the drill press fixed. Column: It is the part that acts as a backbone and provides support to the drill press. Drill press main sliding unit is attached to column as well and moves on the column. Work bench: it is a table attached to the column, it is used to hold the workpiece in place during operation. It consists of rails, through which bolts can slide and the fix the work piece on table at any location. Drill head: it is the top most part of drill press that contains the power spindle. 1.2 Radial drill Second type of frill press used in industries is the radial drill press. This type of drill press has larger range of cutting holes therefore it is used for large parts. Like upright drill press it also consists of Base, Column, Work bench and Drill head. In addition, it consists of one additional component that is explained below. (Groover, 2010) Radial arm: it is the component responsible for higher drilling range of radial drill. It can slide vertically on the column and also it can be rotated about the column and set at any angle. Drill head is fixed on the drill arm so it can slide across the radial arm and can be set at any distance from the column. 1.3 Gang drill Third and last type of drill press found in industry is gang drill. In this type of drill press, several upright drill press are arranged in a line that work independently but share the same working table. Therefore, this type of drill is used for cutting holes in sequence on same work piece or to perform sequence of operations like drilling, reaming, counter sinking, tapping, etc.ÂÂ   (Groover, 2010) This report will discuss the design for manufacture for the drill press main sliding unit. Material type has already been selected as polymeric material to reduce cost. For testing and feedback purpose, it is decide that initially only 20 units will be manufactured. After the positive feedback, this part will be manufactured commercially with production rate of 350 units per week. Task 1 (a) For a product to be successful, it should satisfy some set of requirements that the market / people demands and also the demands of industry. Functional requirements can be categorized into requirements of market, requirements during operation, manufacturing requirements and compliance requirements. (Rajput, 2008) 2.1 Requirements of market This product is intended for cottage industries as well for large production industries therefore its price should be in the range of 10 to 15 pounds per piece. Other demands of market include it should be easy to transport, high strength, safe to use, maintenance cost should be minimum and its life should be high. Finally, the product should attract people with its good aesthetics. 2.2 Operation requirements Most important requirement is that it should have enough strength to bear all the forces that will act on it during operation. The operation cost of the product that include the maintenance cost should be low. For the safety of the user, sliding motion of drill sliding unit on column should be smooth with less friction offered. High working temperatures are faced in drilling operation, therefore the melting temperature of the part should be high and it should be able to maintain its mechanical properties at high temperature as well. It should be used for variable chuck sizes.ÂÂ   (Rajput, 2008) 2.3 Manufacturing requirements Product should be light weight so that less material is required is required to manufacture it which will reduce its cost. Material requirements is polymeric material. Mass of the part should be just under 1.5 kg. Production time of the part should be such that production part of 350 part per week is achieved. Manufacturing technique for this part is injection molding therefore all the edges of the part should be properly filleted and sides should be drafted. Assembly and disassembly of the part should be quick and easy, fasteners would be used to mount the part on column for easy assembly and replacement of the part when required. (Rajput, 2008) 2.4 Compliance requirements Manufactured part should comply with the standards of The Society of the Plastics Industry so that there is uniformity among the manufactured parts and the replacement of part is easy. For this part standard SPI-B1 or SPI-C1 can be used. (Rajput, 2008) Task 1 (b) 3. Features, Manufacturing Process and Material Selection for DPMSU prototype The material available for manufacturing was polymer which became a basis for us to decide which process was to be followed. Keeping the economics, circumstances and suitability into consideration; injection molding was the most preferable process to manufacture the prototype of the drill press sliding unit. 3.1 Injection Molding Manufacturing Process In correspondence to our decision, Injection Molding is usually the most preferable and suitable process which is used for the manufacturing of materials made up of polymers. This process is highly flexible and diverse, and the products vary greatly in size and shape. Various shapes can be formed as a result of injection molding in a very short amount of time and with a very fine surface finish. (Groover, 2010) Figure 3: Parts of Injection Molding unit The process is very simple and easy to understand. Initially the raw material (plastic in our case) is inserted into the machine through the hooper placed on the top of the unit containing the reciprocating screw. To transport the plastic from the hooper to the mold core, a rotating screw is used which pushes these pieces towards the mold and applies pressure on them. The heaters on the wall around the screw melt down these pieces and eventually the molten plastic forms a highly viscous paste. This molten plastic is accumulated in the mold and the shape of the mold eventually ends up in the shape of the product. The plunging process of the machine makes sure that the mold is completely filled with the molten plastic and there are no further defects or any voids. This is all done due to the high pressure, the plunger exerts on the plastic. In the mold, the temperature drops and the molten plastic solidifies. The clamping unit is then separated with the help of clamping motor drive and chain. The part is then taken out very carefully because if too much force is applied, it might break or deform which might weaken its internal microstructure. This all depends on the way the part is designed and whether the stresses that occur during the removal process, are taken into consideration. Injection molding is an advantageous process in several ways which led us to choose this over any other. Injection Molding can produce parts of several shapes and sizes and in a very short amount of time. The products resulting from this process have very fine surfaces finishes. The labor cost is reduced greatly through this process and it leads it to be very economical. The wastage from Injection Molding is negligible and the remaining plastic can be re melted and used. (Groover, 2010) 3.2 Material When designing a drill press sliding unit, the most important parameter to consider was temperature. During drilling operations, the temperature might rise up very rapidly so a material with a very favorable temperature stability was required. The variation of material properties with change in temperature should be as low as possible. The second parameter to decide the material was the response of the material to forces and stresses applied during the molding process. Stresses not only played a role in deciding the material but also played a major role in the designing phase. These factors collectively contributed in deciding which material was to be used. Every material had some shortcomings and strengths and neither of the materials behaved appropriately in every condition but it was up to us to decide the point till which we could compromise on the temperature response without compromising on the stress profile. This influenced us to go for poly ether imide which is commonly refe rred to as PEI. This material remains very stable thermally up to temperatures like 200 o C (Frese et al., 2007). Not only that but it offers a very high resistance to wear a high speeds and pressures. DPMSU is a process which involves high pressures to drill the holes during operation and therefore, it needs continuous sliding. PEI becomes very suitable for such conditions. It is also highly resistant to thermal cracking and is denser than the other polymers. Apart from all these qualities, PEI is also very resistant to any sort of reaction influenced by chemicals (acids, alkalis, fuels and alcohols etc). Most importantly, it offers a very high tensile strength of 16000 psi throughout a very vast range of temperatures from -270 oC to 300 oC. PEI has very good mechanical properties at very high temperatures and very likely for our project. The only issue was that due to such an impressive range of advantages, PEI is relatively more costly than the other polymers. Despite that, our t otal cost is still very low if compared to the material cost of metals. (Frese et al., 2007) PEI offers a very wide range of applications in industry due to a lot of factors. It is very robust and has high strength which makes it very promising for usage. Some of its most common applications are as followed: It is used in the electronics industry specially for making integrated circuits. The reason for this is its high thermal stability and effective usage at a diverse range of temperatures. (Kuznetsov, 2000) It is used in aerospace industry due to the high strength it offers. (Kuznetsov, 2000) It is used in automotive industry due to its incredible surface finishing. (Kuznetsov, 2000) Task 1 (c, e) 4. Design Considerations We do know that the most suitable process for mass production of polymer is Injection molding. Keeping that in mind, we now have to consider the parameters and steps to be followed in order to cut down the production cost and production time as much as possible. 4.1 Avoid Sharp Edges Sharp corners are the biggest source of stress concentrations and high stress concentrations lead to point failures and crack initiations even under normal loading circumstances. The primary approach while designing this work piece would be to avoid as many sharp edges and practically avoidable and replace these edges with fillets and round corners. This will distribute the stress on the surface and will increase the part life under fatigue or creep loading. Work pieces with sharp corner becomes very vulnerable to surrounding and operating conditions and will behave in a very un-predictable manner under loading conditions. (Tang, 2008) 4.2 Avoid Sinking and other post-process deformations Due to difference in the exposure temperatures, all layers within the material cool down at different rates with respect to each other. This leads to the outer surfaces solidifying faster than the inner layers. This causes stress in the inward direction and the shape of the piece starts to change. The outer layers start sinking into the workpiece and this phenomenon becomes more dominant when there are multiple geometries of different thicknesses. To avoid such a situation, the thickness of the work piece should be kept as low as achievable according to the design. Sinking leads to discontinuities in the piece geometry and also induces unfavorable internal stresses. (Tang, 2008) 4.3 Material Optimization During manufacturing, attention should be given to save as much material as possible without compromising the integrity of the work piece. The designing should be done in such a way that the weight of the work piece is minimum possible with optimum required strength. This will not only lead to more weight but will increase the cost unnecessarily. Care has to be taken when extra material is made after the molding process. (Zhang, 2007) 4.4 Drafts For easy removal of the work piece from the mold, it is essential to leave some clearance so that the mold doesnt stick to the work piece. If it sticks, it might become difficult to remove the work piece and it might end up deforming the work piece. In such cases, it is preferable to keep the draft angle from 1 degree to 5 degree. This angle will give ample clearance to the work piece and will avoid any unfavorable situation. This parameter is essential for the smooth running of this process. (Zhang, 2007) 4.5 Material response to the mold It is very information that the material responds to the process appropriately. The material properties play the main role in defining the processes to be followed or the steps to be taken. The material should be decided very carefully keeping into consideration, all the problems and complications it might face in the process. The molten form of the material should be such that it accommodates itself perfectly within the mold and cover all the fine details within. The material should not sink after solidification and neither should it warp. (Wu, 2006) 4.6 Minimum work to be done of the work piece after molding The manufacturing should preferably be done by an experienced person. This will result in a much better and refined product and minimum refinement work will have to be done after the manufacturing. The mold plays an equally important role in the look of the product. A mold with a smooth inner surface will produce a very smooth outer surface of the work piece and hence very little work will have to be done to give the work piece a final touch before being used. (Wu, 2006) 5. Concerns and recommendations There are few concerns which have to be taken into consideration during our design and manufacturing process of DPMSU. These are as followed: If we are to run a machine, it is to be made sure that all the written information on the manual is communicated to the user as a lot of safety hazards are particularly mentioned on the user manuals. These manuals also contain procedures to be followed and precautions to be made so reading these documents is recommended before the usage of the machine, for safe and smooth operation. It is very crucial that the product is safely removed from the mold after solidification and nothing is damaged during its removal process. It is therefore essential that necessary clearances may be left in the mold and draft angles are taken into consideration while designing the mold. These angles greatly assist in the removal of the work piece after it has solidified. During the design process, it is to be taken into consideration that the stress is evenly distributed through the work piece and nowhere in the specimen should the stress be high enough to initiate a crack or cause any structural failure. Sharp edges and corners are the biggest source of high stress concentrations and must be replaced with the contoured surfaces in order to avoid stress concentration areas which may lead to mechanical failure of drill press main sliding unit during drilling operation. The mold plays a major part in defining how much time a particular process will take, how much of a share would labor cost have in the total cost and how good of a surface finish would be obtained. If these parameters are well understood and well implemented, work piece removal becomes very time and cost efficient. The machine should be completely utilized and hence the ejector pins should be taken into full use while removing the work piece. For minimum wastage, it is important that material with the most suitable condition and position is used throughout the operation. The machine should be used by an experienced person, who will make sure that minimum material is wastage after the process. As PEI is relatively more costly than other polymers, this consideration becomes important. It is necessary that the work piece is consistent and regular in dimensions. It is also to be considered that minimum post-process work is done and the manufactured specimen is gone through minimum finishing processes. To achieve this, the mold should be very smooth and the machine operator should be very experienced. Task 1 (d) Previously, injection molding is suggested for the prototyping of the component. Injection molding is also suitable for batch production of drill press main sliding unit but following things must be taken into consideration: If injection speed is high with less solidification time, it may lead to the deformation of material with time. To prevent this issue, speed of injection molding and time for solidification must be optimized in batch production. Drill press main sliding units is used to hold the drill bit and holder. Due to machining operation, temperature of the assembly may rise. Moreover, unexpected stresses on the component may occur. So, manufacturing method must yield polymeric component with optimized thermal conditions to avoid any catastrophic failure later on. (Rajput, 2008) Variations in dimensions is a common issue in polymeric components. To avoid this, synthetic hardening resins could be used while doing injection molding. These resins may enhance surface hardness of the component. (Tang, 2008) Porosity and air bubbles left in the component during manufacturing may lead to brittle failure later on. To avoid this, porosity must be prevented to occur. (Tang, 2008) References Groover, M. (2010). Fundamentals of modern manufacturing. 4th ed. New York: JOHN WILEY SONS, INC. Rajput, R. (2008). A textbook of manufacturing technology. 1st ed. New Delhi: Laxmi. Tang.Z.Y. (2008). :Plastic Mould Designer Guide[M],edited by Mechanical Industry Publishing House,Beijing. Wu.Z.Z,Wang.Q,Pang.Y.X,Zhang.H.A:Plastic Mold Design Guide,edited by National Defense Industry Press,Beijing(2006). Zhang W.H:Injection Mold Design of Practical Tutorial[M],edited by Chemical Industry Press,Beijing(2007 T. Frese et al., Electret Properties of Polyetherimides: Influence of Water Content and Comparison with Other High-Temperature Polymer Films, Macromol. Mater. Eng., vol. 292, pp. 582-587, February 2007. Kuznetsov, One-pot polyimide synthesis in carboxylic acid medium, High Perform. Polym., vol. 12, pp. 445-460, June 2000.

CanGo’s Financial Analysis Essay

Following up with our initial analysis last week, NewGen had the opportunity to review CanGo’s financial statement. The success of a business depends on its ability to remain profitable over the long term, while being able to pay all its financial obligations and earning above average returns. NewGen leveraged our knowledge of Investment rations, breaking our analysis down into four (4) key areas, efficiency, financial leverage, liquidity and profitability. Attached you will find our financial analysis summary matrix. 1.Efficiency Ratio We began with a look at your efficiency ratio, concentrating on your receivables turn over for the past year. This reflects the time between your sale and actual collection. If a company’s Turnover Rate is significantly lower than industry norms, there could be an underlying reason such as poor collection methods, high-risk customers or low sales. With CanGo’s Efficiency Ratio for receivables turnover was at 1.51, there is room for improvement and a closer look needs to be performed to pinpointed where the problem lies. We next looked at CanGo’s Inventory Turnover as a measure of CanGo’s inventory management efficiency. In general, a higher value indicates better performance and lower value means inefficiency in controlling inventory levels; CanGo’s was 1.56. This lower inventory turnover ratio may be an indication of overstocking which may pose risk of obsolescence and increased inventory holding costs (Accounting Explained, 2012). 2.Financial Leverage Taking a look at CanGo’s equity ratio for how much they relied on their debt, we were surprise to see a low debt to equity ratio of 7.57, thereby enabling CanGo to utilize more of their revenue for their future plans (Financial Dictionary, 2012). 3.Liquidity Ratio Our Review of CanGo’s Liquidity included the current ratio, the quick ratio and the operating cash flow ratio or Working Capital. a. Current Ratio reflected a 1, which is low if CanGo wishes to position themselves to turn short-term assets into cash to cover debts or assist with the planned upgrades. b. Your Quick Ratio fell below a 1 to .95. As a common rule of thumb, a quick ratio of greater than 1.0 means a company is sufficiently able to meet their short-term liabilities. With CanGo’s falling below this threshold, could be indicative that your over-leveraged, struggling to maintain or grow sales, paying bills too quickly, or collecting receivables too slowly. This ties into our comments above on yor efficiency ratio (Investigatinganswers, 2012). c. Working Capital for the past year reflected a negative balance almost 8.5m that will seriously impact on banking institutions percentage against planned activities. 4. Profitability NewGen’s final analysis was on CanGo’s profitability looking at your Return on Assets and Sales. CanGo’s return on assets reflected a .023 indicative that your more asset-intensive and must reinvest more money to continue generating earnings (About.com, 2012). Similarly, CanGo’s Return on Sales (ROS) was .17 (Investopedia, 2012).

Analysis and Interpretation of Don Juan

Analysis and Interpretation of Don Juan canto 1 stanza LXV to LXX: Don Juan was written by Lord Byron. He started writing it from 1818. The manuscript was not complete at the time of Byron's death in 1824. Byron coined the term â€Å"Byronic Hero†. Don Juan is definitely a Byronic Hero. He has all the Characteristics of a Byronic Hero. This poem constantly takes me back to the 1800s, because at that time women had no rights at all. If they married someone then they were treated like property of their husbands and if they stayed single then their parents dictated every single thing she did with every single person.For most part women were not allowed to stay single unless they were nuns or prostitutes. Even when they were married they were not allowed to hold control of inherited wealth. They did not have the right to own a slave or even vote. Women were economically dependent. If a woman did something wrong and people find out about it, she would be tainted and blemished forev er and also banished from society but if a man does the same thing or even worse, he could still be able to hold his head up high in society. Julia married Alfonso only because she had to. Alfonso never showed his jealousy because nobody likes a jealous person.Alfonso cared about what people thought and he was cleaver and careful. He never wanted people to know about his illegal affairs. I personally think Donna Inez is a psychopath and a Sociopath both. I mean why else would she use her son to destroy the relationship of her lover and his wife. Julia is not as complicated as Inez. Julia does not realize what Inez had in her mind. I think she thought Inez actually wanted to be her friend. Being a simple girl Julia probably didn’t know about Alfonso and Inez’s affair. When Juan was a child Julia showed affection for him but that was just normal and innocent.When Juan hit puberty something changed between both of them. They felt attracted to each other. As a grown woman Julia realized why she was feeling this way. But Juan is completely different. His mother never let him mix and mingle with people of his own age. At first he didn’t even realize what was happening to him. This poem follows a third person point of view. In these stanza’s Byron talks about lot of important issues but the tone is always humorous and satiric. Don Juan is a lot like Byron himself. The difference is Byron was highly educated and Juan had no interest in that line.

Povertyin the World - 811 Words

Poverty evokes various definitions depending on the audience and perhaps the purpose or context that it is used. Limiting the definition of poverty to a ‘value judgment’ is of little use in terms of agreeing on a definition for the purpose of comparison and measurement between groups (Sen 1979, p.285). A clear definition of poverty supports and indicates the process for measurement, and as such would also assist in determining the focus and approach for development (Clark 2012; Ruggeri, Saith Stewart 2006, p.19). In reviewing Oxfam Australia’s (Oxfam) Close the Gap campaign, it is necessary to identify the approach that is taken in defining poverty in order to gauge the scope of the project, the development of the approach used, and to quantify the change that occurs. Oxfam itself has identified Close the Gap as a human rights campaign that aims to close the life expectancy health gap of 10-17 years for Aboriginal and Torres Strait within a generation (Holland 2014, p.46). Vizard in her exploration of Sen’s capability approach (2005, p.24), emphasises the marriage of capabilities with human rights, citing poverty as one of the key exclusions to fundamental freedoms and human rights, thus expanding the definition of poverty into a multidimensional one. Health is one of the dimensions included in the rights approach, which suggests that the abuses of human rights result in poverty and are also a result of poverty (OHCHR 2006, p.16). Along with a multidimensional